​​​​​​​​​​​​    

                                          GABION SUPPLY ... a LWECO Group LLC Company    

                                                                                                                                         Call Us Toll Free: 866-391-6295

    GABION "RENO" MATTRESSES

Copyright © GABION SUPPLY. All rights reserved.

DURA-FLEX GABION MATTRESSES aka "Reno Mattresses" are low profile gabions (6" - 9" - 12" - 18" deep) constructed of hex shaped double twisted 13 gauge steel wire mesh and available in Galvanized, Galfan or Galvanized with PVC Coating

The edges are reinforced (selvedged) with heavier 9 gauge wire and the mattress is divided with internal partitions to form uniformly spaced cells 

Each Reno Mattress is pre-assembled in the factory, knocked down and bundled flat for common carrier shipping  

Reno Mattresses are commonly used for slope stabilization on steep hillsides, channel linings, bridge protection and river bank erosion control   

Following  job site assembly, Reno Mattresses are then filled with rocks, creating a durable, flexible, permeable, monolithic structure 

Specifications meet or exceed ASTM  A 975-97
 
Standard mesh openings: 2-1/2" x 3-1/4"   (6x8 cm)

Standard sizes are shown below:

 Unit Size          Weight - Galvanized       Weight - PVC        Capacity 
 9' x 6' x 6"                     36 lbs                            45 lbs            1 cu yd
 12' x 6' x 6"                   48 lbs                            58 lbs      1.33 cu yds
 9' x 6' x 9"                     41 lbs                            49 lbs         1.5 cu yds
 12' x 6' x 9"                   53 lbs                            63 lbs            2 cu yds
 9' x 6' x 12"                   51 lbs                            56 lbs       2.67 cu yds
 12' x 6' x 12"                 56 lbs                            59 lbs       2.67 cu yds 

Special Sizes:

* 18" and 24" Deep     * Jumbo 99' long X 1' Deep rolls

Call for price and availability   1-866-391-6295



DURA-FLEX™ Galvanized Gabion Mattress

General Description:
The DURA-FLEX™ gabion mattress is a mattress shaped container manufactured from heavily galvanized wire to form a flexible and effective surface protection to defend against erosion and scouring. The flexible wire mesh will accommodate significant deformation without failure. The base and sides of the mattress are made of a single sheet of wire mesh (main panel). Partition panels (diaphragms) are made of the same wire mesh as the main panel and are attached to the base of the main panel dividing the gabion mattress into 3 foot cells. The lid is formed either by a single sheet or in rolls of a specified length from the same wire as is in the main panel.

Mesh:
The mesh shall be woven into a hexagonal pattern with the joints formed by twisting each pair of wires through three and a half turns. Because of this appearance, the joints are often termed triple twisted. The mesh opening shall be hexagonal in shape and uniform in size measuring 2-1/2 inches by 3-1/4 inches.

Wire:
All wire used in the fabrication of the gabion mattress and in the lacing operations shall conform to Federal Specification QQ-W-461H, Class 3, Finish 5, soft, and have an average tensile strength in accordance with the current ASTM A 641, Table 2, measured before fabrication of the netting. The nominal diameter of the wire used in the fabrication of the netting shall be 0.0866 inches minimum, subject to diameter tolerance in accordance with the current ASTM A 641, Table 3.

Elongation of Wire:
Tests shall be conducted on the wire before fabrication on the mattress on a sample 12 inches long. Elongation shall not be less than 12%.

Zinc Coating (Galvanizing):
All wire used in the fabrication and construction of the gabion mattress shall be galvanized according to ASTM A 641, Table 1. The minimum weight of the zinc coating shall be according to the table following when tested in accordance with ASTM A 90.

Description:

Nominal Diameter of Wire - 0.0866 in (2.2mm) minimum

Minimum Weight of Coating- 0.79 oz/sq ft

Mesh and Lacing

Selvedge

0.106 inches (2.7mm) minimum

0.80 ozs / sq ft

Adhesion of the zinc coating to the wire shall be capable of being wrapped in a close helix at a rate not exceeding 15 turns per minute around a cylindrical steel mandrel having a diameter 3 times the nominal wire diameter being tested. After the wrap test is completed, the wire shall not exhibit any cracking or flaking of the zinc coating to such an extent that any zinc can be removed by rubbing with bare fingers.

Selvedges:
All edges of the mattress including end panels and the diaphragms, shall be mechanically connected in such a way as to prevent unraveling of the mesh and to develop the full strength of the mesh. The wire used for the selvedge shall have a diameter greater than that of the wire used to form the mesh.

Lacing Wire:
Sufficient lacing and connecting wire shall be supplied with the gabion mattress for all wiring operations. The nominal diameter of lacing wire shall be 0.0866 inches minimum.

Diaphragms:
According to engineering and design requirements the mattress shall incorporate internal diaphragms to form cells having a nominal length of three feet. The internal diaphragms shall prevent rock migration within the gabion mattress unit.

Stone Size:
The DURA-FLEX™ Heavy Duty Mattress was designed specifically to accommodate stone size of 3 to 6 inches (75 -105mm). Only hard durable stone shall be used as mattress fill.

Installation / Placement:
On channel slopes, the mattress shall be placed perpendicular to the flow in the channel with the shorted dimensions of the diaphragm going up and down the slope. On the channel bed, the mattress shall be placed so the flow runs parallel with the short dimension of the mattress compartment, while the width of the mattress runs across the channel bed. An approved corner closure tool shall be used to adjoin adjacent mattresses to insure a tight, neat seam and minimize mattress wire joint deformation.

* GABION SUPPLY reserves the right to amend these specifications without notice.

DURA-FLEX™ mattress gabion material is manufactured according to ASTM A975-97 guidelines for Double Twisted Hexagonal Wire Mesh Gabions


LINK --- DESIGN GUIDELINES FEDERAL HIGHWAY DEPT - DOT